Home > Tech Tips > Brake Pedal Guidelines Solution by: totalwebsystems  
Sales for Business > Consumers (B2C)
From 1st July 2021 Rally Design will not be able to process orders to retail EU customers with a product value less than £135.00 (€150.00). Above €150.00 local customs may charge VAT, import duty and handling charge. Additionally postal operators and couriers may charge a fee to collect these charges. Please note, this does not apply to UK consumers or EU B2B customers. David Elderfield, Managing Director. Last Updated 01/07/2021.
Shopping Cart
Your cart is empty!
0 items
Go to Checkout
Your Account
Your Email Address
Your Password
Did You Know?
There are currently 78 guests online.

120,028,639 visitors online since Thursday 30 September, 2004

Brake Pedal Guidelines by Scott Gillespie

Wilwood pedal assemblies and integrated balance bars have been designed specifically for racing applications. Properly set up, this assembly will allow for the precise adjustment of front to rear brake bias. The advantages of an adjustable balance bar and dual master cylinders are:

  • Brake proportioning can be adjusted by use of different sized master cylinder bores for front and rear brakes.
  • Front to rear brake balance can be fine tuned by adjusting the balance bar.
  • With two independent hydraulic systems, should one master cylinder fail, the other system may remain functional.
Brake pedals should be mounted securely. When possible, keep the master cylinder reservoir level higher than the horizontal plane of the calipers to prevent excessive fluid drain back which can result in double pumping of the pedal. If this is not possible, a two pound residual pressure valve should be plumbed into the brake line at the exit of the master cylinder to prevent fluid drainback. (Do not confuse the two pound valve with the ten pound version; the ten pound valve is for use with drum brakes only).

Brake pedals should be free to return when no pressure is being applied, allowing the master cylinder pushrod to return to it's undepressed position. In some cases, the master cylinder spring (internal) may not be strong enough to fully return the pushrods; in this case an additional pedal return spring can be used. There are two important items for consideration:

1. The brake pedal should have an adjustable return stop on it when a strong pedal return spring is used. This prevents the master cylinder from excessively banging the snap ring stop inside the master cylinder bore (visible under the rubber boot). Adjust the stop so that the pedal stops returning at the point when the master cylinder piston retracts against the snap ring (Fig. 1). 2. The master cylinder piston must fully retract. If the master cylinder piston is not allowed to fully retract when the brake pedal is not applied, the primary inside seal will not return past the small pressure relief hole (visible within the master cylinder reservoir on some master cylinders). This can cause excessive residual line pressure and contribute to brake drag and overheating condition, (Fig. 1 detail A).

Fig. 1. Brake Pedal Guidelines

This article was published on Friday 25 March, 2011.
Best Sellers
01.Hose Fitting Copper Washer - 3/8 & M10
02.Hose Fitting Olive #3
03.#3 Stainless Braided Brake Hose
04.Open Wheel Nut - 12mm x 1.5 - 19mm Hex - 60 Taper
05.Standard Plus 25mm - 63mm Long - 12mm x 1.5 Ford Stud
Featured Products
Spherical Bearing Top Mount - Rubber Bonded
Spherical Bearing Top Mount - Rubber Bonded

2020 Catalogue Request
Follow us with Rally Design for iPhone, iPad and iPod touch on the iTunes App Store
Follow us with Rally Design for Android on Google Play
Rally Design Limited • Unit 4 St. Augustine's Business Park, Estuary Way, Swalecliffe, Kent, CT5 2QJ
Vehicle Identification: References to vehicle marques such as Ford, Vauxhall, Westfield, Caterham etc. are for vehicle fitment identification purposes only.
These references must not be used to imply the vehicle manufacturers have been involved in the design of these products nor endorsement of same.
Product Images: The images shown on this website are for illustration purposes only and may not be that of the actual product. If you are unsure please ask.